MFlenses — новая жизнь в цифровую эпоху
MFLenses 2026

Форум объективов с ручной фокусировкой

Исследуйте мир старых объективов через заметки о ремонте, реальные тестовые снимки и подробные архивные темы с множеством изображений.

Исследуйте мир старых объективов через заметки о ремонте, реальные тестовые снимки и подробные архивные темы с множеством изображений.
В центре внимания

Место для партнёра на главной странице форума.

Disassembling Meyer-Optik Primoplan 58/1.9
Предыдущая тема :: Следующая тема  


Reply

I am trying to clean the internal glass on a newly acquired Primoplan 58/1.9 and I am having problems with disassembling the front part of it. It seems pretty straightforward at first but I can't figure out how to remove the front nameplate. Any ideas? Thanks...


Reply

Нажмите здесь, чтобы посмотреть на Ebay

You need this tool or sink stopper (plug) what has exact diameter and made from hard gum.


Reply

Yeah, that's the one thing that I still don't have. However, I look at the nameplate ring (it is actually a large conical part like in many macro lenses) and it looks like that thread on the filter ring above it is narrower and won't let the ring to come off. I guess it's just an optical illusion Smile


Reply

Update: I was right... The nameplate could only be removed with the front filter ring as a single item. After the small retaining screw on the inner side of the front ring is removed, the entire front part can be unscrewed, which gives the access to the front optical unit. Unscrew that one and you get straight to the diaphragm. The rear optical assembly can also be easily removed with a lens wrench so the diaphragm becomes accessible from both sides.


Reply

pirius писал(а):
Update: I was right... The nameplate could only be removed with the front filter ring as a single item. After the small retaining screw on the inner side of the front ring is removed, the entire front part can be unscrewed, which gives the access to the front optical unit. Unscrew that one and you get straight to the diaphragm. The rear optical assembly can also be easily removed with a lens wrench so the diaphragm becomes accessible from both sides.


It would be nice if you take photos from each steps and publish it here, I think some people will happy to read it and use it when need it. Many thanks in advance!


Reply

Sorry, I have already assembled it back. But it's easy, there is not much to show. If you look inside the lens from the front you'll see a tiny screw. Loosen it up, then grab the front part of the lens firmly (the filter ring) and unscrew it counter-clockwise. After that it's just a regular disassembly with a spanner wrench.

So the rubber tool was not necessary, but I have ordered it anyway Smile

BTW, I've tried the lens and I think it's awesome!


Reply

pirius писал(а):
Sorry, I have already assembled it back. But it's easy, there is not much to show. If you look inside the lens from the front you'll see a tiny screw. Loosen it up, then grab the front part of the lens firmly (the filter ring) and unscrew it counter-clockwise. After that it's just a regular disassembly with a spanner wrench.

So the rubber tool was not necessary, but I have ordered it anyway Smile

BTW, I've tried the lens and I think it's awesome!

Laughing No problem, rubber tool is useful. I like this lens too pretty much, congrats for your new tool.

Try to hunting down Helioplan 40mm or 4cm from Meyer it has even better IQ Wink


Reply

pirius писал(а):
Update: I was right... The nameplate could only be removed with the front filter ring as a single item. After the small retaining screw on the inner side of the front ring is removed, the entire front part can be unscrewed, which gives the access to the front optical unit. Unscrew that one and you get straight to the diaphragm.


pirius писал(а):
... If you look inside the lens from the front you'll see a tiny screw. Loosen it up, then grab the front part of the lens firmly (the filter ring) and unscrew it counter-clockwise. After that it's just a regular disassembly with a spanner wrench.


I have removed the small retaining screw on the inner side of the front ring but the front part can NOT be unscrewed. I have tried to unscrew it counter-clockwise firmly as i can.
My intention is to clean the diaphragm from excessively oiling.
What to do?