MFlenses — новая жизнь в цифровую эпоху
MFLenses 2026

Форум объективов с ручной фокусировкой

Исследуйте мир старых объективов через заметки о ремонте, реальные тестовые снимки и подробные архивные темы с множеством изображений.

Исследуйте мир старых объективов через заметки о ремонте, реальные тестовые снимки и подробные архивные темы с множеством изображений.
В центре внимания

Место для партнёра на главной странице форума.

Canon Elan 7 question
Предыдущая тема :: Следующая тема  


Reply

If I'm using a manual lens, and set the camera to Aperture Priority, will it read the light coming in and auto pick a shutter speed, or do I have to place it on full manual?

Thanks!


Reply

hard to say Confused

I'm not sure but I think all EOS models meter light with open aperture and then, just before the shot - calculate the exposure by information it gets from the electronics of the lens? so without this information you get over(?)exposure?


Reply

The manual for your camera (English) http://downloads.canon.com/cpr/software/camera/EOS_Elan_7_manual.pdf

I think the film cameras work like the EOS DSLR, In aperture mode, the camera will set the appropriate shutter speed. That is hoe my T3i works.

Phil


Reply

I have noticed that my EOS DSLR's light readlings will differ from what they should be, such that overexposure sometimes occurs. This problem seems to compound itself as the aperture values increase (smaller diameters). The reason for these discrepancies is that the EOS does indeed depend on some feedback from the lens for correct exposure and that setting it to Aperture Priority by itself may not be enough.

Here's the problem, though: I don't get this with all lenses. Some lenses my camera behaves normally with, others it doesn't. So it's almost on a case-by-case basis. My advice? Take a light meter with you, or another camera with a meter you trust and use it to meter the scene. Or -- take along an EOS lens with you and mount the EOS lens to get a meter reading of the scene, then dismount the EOS lens and remount your manual focus one, adjust exposure, and shoot. It's a PITA, sure, but what else can you do? Oh, from what I've read -- these chipped adapters work pretty well in preventing this. So you might check into a chipped adapter for your lens.


Reply

BigMack3000 писал(а):
If I'm using a manual lens, and set the camera to Aperture Priority, will it read the light coming in and auto pick a shutter speed, or do I have to place it on full manual?

Thanks!


This is from photonotes.org

photonotes.org писал(а):

Old and new stop-down metering styles.

The earliest Canon EOS cameras and the later models handle stop-down metering in two different ways. It’s easy to tell which style your camera uses.

Turn your camera on and remove any lens that may be attached to it. With no lens attached to the bayonet press the shutter release down halfway and look at the aperture setting in the viewfinder or top-deck panel.

If the display reads “1.0” (or any number other than “00”) then you have the old stop-down metering style. Only a few ancient EOS film cameras use this method.

If the display reads “00” then you have the new stop-down metering style. Most EOS film cameras and all EOS digital cameras support this.

How to use the really old-style stop-down metering style (display shows something other than “00”).

If you attach a non-EF lens to your older Canon EOS film camera, the camera notices that the lens doesn’t have a working computer and goes into stop-down metering mode. It nonetheless displays a full range of apertures, which you can set from 1.0 to 32.

Set the camera’s aperture setting to 1.0 and leave it there.

Do not set the camera’s aperture value to match that of the lens. In fact, I don’t know why the camera lets you change the aperture setting at all, since it only screws things up by overexposing the image.

If your lens has an adjustable aperture (usually an aperture ring on the barrel) you must do the adjustment on the lens itself, not the camera. This will obviously vary the amount of light entering the camera. The camera reads it and meters from that accordingly.

Now, since the camera isn’t capable of adjusting the aperture setting on the lens it can’t work in P (program), Tv (shutter speed priority) or PIC (icon) modes with such a lens, but it’ll work just fine in Av (aperture priority) and M (manual) modes.

In Av mode you set the lens aperture using the lens aperture ring and the camera’s aperture setting to 1.0 and then camera will set a shutter speed automatically. In M mode you set the aperture using the lens aperture ring and then set the shutter speed on the camera yourself.

One other note - some older EOS cameras have the annoying inability to remember aperture settings when you switch from one mode to another. Some models, such as the EOS 620/650 or 10/10s, automatically switch the aperture value to 5.6 whenever you go into Av and M modes. Since the aperture value must be set to 1.0 when using stop-down metering and a manual lens you have to dial the aperture back every single time you enter either mode. This is particularly annoying in M mode, because since these cameras lack a rear command dial you have to hold the partial metering button whilst rotating the main dial. Oh, well.

How to use the new-style stop-down metering style (display shows “00”).

If you attach a non-EF lens to your newer Canon EOS camera, the camera notices that the lens doesn’t have a working computer and goes into stop-down metering mode, displaying the aperture value 00. This means that the camera knows that the aperture setting is not under its control and will not let you set the aperture electronically. This metering style makes a lot more sense than the old method.

If your lens has an adjustable aperture (usually an aperture ring on the lens barrel) adjust it now. This will obviously vary the amount of light entering the camera. The camera reads it and meters from that accordingly.

Now, since the camera isn’t capable of adjusting the aperture setting on the lens it can’t work in the Tv mode with such a lens, but it’ll work just fine in the other “creative” modes - P (program), Av (aperture priority) and M (manual). It doesn’t really make sense to use the lens in any of the PIC (icon) modes.

Set the aperture using the lens aperture ring and the camera will set the correct shutter speed in all other modes except M, where you’ll have to set the shutter speed yourself. Generally, Av mode is probably the most convenient
.


Reply

Thanks guys! This all helped a lot. My camera reads "00" with no lens. I'll try it out with a helios this weekend.