MFlenses — новая жизнь в цифровую эпоху
MFLenses 2026

Форум объективов с ручной фокусировкой

Исследуйте мир старых объективов через заметки о ремонте, реальные тестовые снимки и подробные архивные темы с множеством изображений.

Исследуйте мир старых объективов через заметки о ремонте, реальные тестовые снимки и подробные архивные темы с множеством изображений.
В центре внимания

Место для партнёра на главной странице форума.

Failed cerium oxide polishing on an Elmar 5cm 2.8 front lens
Предыдущая тема :: Следующая тема  


Reply

Hallo all,

I had had in the past good success at removing scratches from a couple of inexpensive japanese lenses (cosina 50mm front, 55mm tomioka style rear flat lens, much scratched) by polishing them manually with cerium oxide)

Today I tried to remove some fungus acidity signs from the rear of a front lens of an Elmar 5cm 2.8 from 1957 (2nd version)

I had already had some good success with the rear lens of the same Elmar, after polishing all the fungus signs had been removed (coating had been partially removed but the effect was insignificant plus it is a "character" lens in my view so some less coating doesn't matter much in such case).


Well I repeated the treatment on the front and the result is an opacized surface.

Any suggestion?

Should I go on with a new type of cerium (has anybody a type to suggest)?

Best regards and thanks in advance


Reply

pleto писал(а):
Hallo all,

I had had in the past good success at removing scratches from a couple of inexpensive japanese lenses (cosina 50mm front, 55mm tomioka style rear flat lens, much scratched) by polishing them manually with cerium oxide)

Today I tried to remove some fungus acidity signs from the rear of a front lens of an Elmar 5cm 2.8 from 1957 (2nd version)

I had already had some good success with the rear lens of the same Elmar, after polishing all the fungus signs had been removed (coating had been partially removed but the effect was insignificant plus it is a "character" lens in my view so some less coating doesn't matter much in such case).


Well I repeated the treatment on the front and the result is an opacized surface.

Any suggestion?

Should I go on with a new type of cerium (has anybody a type to suggest)?

Best regards and thanks in advance


Solved with full success.

I ordered a fresh cerium batch in powdered state. I mixed it 1:1, the lightest mixture. With several application I obtained a perfectly clear lens.

Now the Elmar performs almost as new


Reply

Thank you for info!


Reply

pleto писал(а):
pleto писал(а):
Hallo all,

I had had in the past good success at removing scratches from a couple of inexpensive japanese lenses (cosina 50mm front, 55mm tomioka style rear flat lens, much scratched) by polishing them manually with cerium oxide)

Today I tried to remove some fungus acidity signs from the rear of a front lens of an Elmar 5cm 2.8 from 1957 (2nd version)

I had already had some good success with the rear lens of the same Elmar, after polishing all the fungus signs had been removed (coating had been partially removed but the effect was insignificant plus it is a "character" lens in my view so some less coating doesn't matter much in such case).


Well I repeated the treatment on the front and the result is an opacized surface.

Any suggestion?

Should I go on with a new type of cerium (has anybody a type to suggest)?

Best regards and thanks in advance


Solved with full success.

I ordered a fresh cerium batch in powdered state. I mixed it 1:1, the lightest mixture. With several application I obtained a perfectly clear lens.

Now the Elmar performs almost as new


By curiosity, what are you mixing the powder with? I've read about distilled water etc